描述
Most under-cabinet lighting fails for one reason: it needs a switch that nobody wants to touch with wet hands. Motion sensing removes the switch from the problem entirely, which is why this format replaced the wired puck light almost everywhere it was installed.
The bar is a slim aluminium-profile strip with a diffused face, so the light spreads evenly across a worktop instead of throwing hotspots. Three colour temperatures are switchable on the unit itself: a warm tone close to a filament bulb, a neutral working white, and a cooler daylight setting for detail work. The sensor covers a short passive-infrared cone, which means it reacts to movement in front of the bar rather than to a hand wave at the side.
Power comes from an internal rechargeable cell charged over USB, so there is no wiring and no electrician. That is the practical argument: the light mounts with adhesive or screws to the underside of a cabinet, onto a wardrobe shelf, or inside a stair riser, and it never needs to reach a socket. On the shortest length a charge covers weeks of intermittent use, and the longest length naturally draws more.
Four lengths and two finishes cover the realistic installations: 20cm and 30cm for a wardrobe or a single cabinet run, 40cm for a kitchen worktop section, and 50cm for a full counter span. Black and silver match the two most common cabinet interiors.
A light you never switch on is the only light that actually gets used.
How The Sensing Works
- ✦Passive infrared motion sensor triggered by movement in front of the bar, not by a hand wave.
- ✦Three switchable colour temperatures: warm, neutral white and cool daylight.
- ✦Diffused face across an aluminium profile, so the spread is even rather than spotlit.
- ✦Internal rechargeable cell charged over USB, with no wiring or socket required.
- ✦Mounts by adhesive pad or screws, both included, with no electrician needed.
- ✦Four lengths from 20cm to 50cm, in black or silver.
- ✦Slim profile that sits behind a cabinet lip and stays out of sight from the room.
Electrical & Physical
- TypeRechargeable LED bar with PIR sensor
- Colour temperaturesWarm, neutral white, cool daylight
- Lengths20cm, 30cm, 40cm, 50cm
- FinishesBlack, silver
- ChargingUSB, internal rechargeable cell
- MountingAdhesive pad or screws, both included
- SensorPassive infrared, short range
- ProfileSlim aluminium with diffused face
- InstallationNo wiring, no socket required
- UseUnder-cabinet, wardrobe, stair, pantry
Install Scenarios
The obvious install is under a kitchen wall cabinet, where the bar lights a worktop without casting a shadow from your own body. The second is inside a wardrobe or a pantry, where a ceiling light would never reach the back shelf. The third is a stair riser or a hallway skirting, where a warm low light at foot level is safer at night than a bright overhead switch. Because there is no wiring, the same unit can be moved between these positions without any reinstallation work beyond the adhesive pad.
Technical Questions
How long does a charge last?
It depends on length and how often the sensor triggers. The 20cm bar on the warm setting running a few short activations per evening covers several weeks per charge. The 50cm bar on cool daylight is the heaviest draw and should be expected to need charging roughly every one to two weeks in daily use.
Will it switch on when my pet walks past?
A passive infrared sensor reacts to a warm moving body within its cone, so a cat or a dog crossing directly in front of the bar will trigger it. Mounting the bar higher, with the sensor angled toward the worktop rather than the floor, is the usual fix and also reduces false triggers from draughts.
How is it charged and how long does charging take?
A standard USB cable connects to the port at one end of the bar. A full charge from empty takes a few hours. The cell is internal and not user-replaceable, so the bar is a sealed unit rather than a battery-swap design.
Can it be mounted on a wall rather than under a cabinet?
Yes. The adhesive pad holds on smooth painted or laminate surfaces, and the supplied screws handle anything that adhesive will not grip, such as rough timber or tile. If you use adhesive on a freshly painted wall, give the paint a few days to cure first, otherwise the pad will pull the paint away when removed.
Is the light bright enough to work under?
It is a task and accent light rather than a room light. Under a cabinet it is enough to read a recipe, chop safely and see the back of a worktop clearly. It is not intended to replace a ceiling fixture, and the diffused face is deliberately chosen to keep the output soft rather than harsh.
Dispatched from the EastSupplier network with tracked shipping and a 30-day return window. Every listing is documented, photographed and priced upfront, so what arrives is what you ordered.
Customer Reviews
Payment and Security
您的支付信息已安全处理。我们不存储信用卡详细信息，也无法访问您的信用卡信息。