描述
Soldering a board is a three handed job done with two. One hand holds the iron, one feeds the solder, and nothing is left to hold the board still. The Fifth Hand is the answer every bench eventually arrives at: five flexible arms on a clamped base, a 3x magnifier on one of them, and a joint that stays where you bent it until you bend it again.
The arms are the part that separates a usable station from a toy. Each is a universal joint of 90 mm and 270 mm sections with a Y shaped cradle at the tip, and the assembly holds a board without the spring-back that makes cheap helping hands useless after a month. The clamp base grips the edge of a bench, so the whole station hangs over the work area instead of standing in it, and the base rotates through 360 degrees for a different approach angle without loosening anything. The magnifier is 55 mm across at 3x, and the LED ring around it adjusts through three colour temperatures and eleven brightness steps, which covers everything from a bright bench to a dim corner at night.
Two versions are listed, with and without the illuminated magnifier, and the practical choice is simple: if you solder anything smaller than a through-hole resistor, take the lit version, because 3x magnification plus directional light is what turns a cold joint into a visible one. The packaging measures roughly 30 by 20 cm, the base is a plastic clamp, and the unit is designed to be clamped and unclamped between sessions rather than bolted down permanently.
Two hands, five arms, and a joint that finally stays where you put it.
What Makes It Different
- ✦Five flexible arms with Y-shaped cradles hold a board at any angle
- ✦Universal joints of 90 mm and 270 mm sections hold position without spring-back
- ✦3x magnifier, 55 mm across, with adjustable LED ring
- ✦Three colour temperatures and eleven brightness steps on the lit version
- ✦Clamp base grips a bench edge and rotates 360 degrees
- ✦Frees both hands for the iron and the solder feed
- ✦Suits soldering, rework, jewellery work and craft assembly
Technical Specifications
- Arms5 flexible arms, Y-shaped cradles
- Joint Sections90 mm and 270 mm universal joints
- Magnifier3x, 55 mm diameter
- LightingLED ring, 3 colour temperatures, 11 brightness steps
- BasePlastic clamp, 360 degree rotation
- VersionsWith illuminated magnifier, or without
- ColourBlue or black
- Packaging SizeApproximately 30 x 20 cm
- CertificationCE
- ApplicationSoldering, PCB rework, jewellery, craft assembly
Where It Earns Its Place
Hobby electronics is the obvious case: an Arduino shield, a repaired games console, a drone flight controller with twenty pads in a square inch. Repair benches use it for phone and laptop board work where a hot air station needs the board held flat and off the mat. Jewellers and model makers use the same arms for tiny assemblies that need three points of contact. Anyone who has tried to hold a board with a spring clip and a sponge knows the difference: the board stays where it was placed, the light goes where the work is, and both hands stay on the tools.
The EastSupplier Promise
Sourced directly from vetted manufacturing partners, inspected before dispatch, and priced without distributor layers. If the item arrives outside specification, we replace it or refund it. Every listing on this store is curated by a human buyer, not bulk-imported and abandoned.
Questions Buyers Actually Ask
Q: Do the arms hold their position over time?
Yes, that is what the joint sections are for. The 90 mm and 270 mm segments tighten against each other so the arm stays where it is bent, and the cradle at the tip holds the board rather than letting it slide. Expect to re-tension the joints occasionally with use, as with any flexible arm.
Q: Is the magnifier strong enough for surface mount work?
3x at 55 mm is right for through-hole work, inspecting joints and reading markings. For 0402 components and fine pitch pads you want 5x to 10x, so treat this as the general bench magnifier rather than a microscope replacement.
Q: What is the difference between the two versions?
One has an illuminated magnifier with a LED ring adjustable through three colour temperatures and eleven brightness steps, the other has the arms and base without the light. The lit version is the one to take if you work in the evening or solder fine joints.
Q: Will the clamp fit my bench?
The base is a screw clamp designed for a bench edge, and it rotates through 360 degrees once mounted. Measure the thickness of the surface you intend to clamp to before ordering, since a moulded plastic desk edge or a glass top is a poor host for it.
Q: Can I use it for things other than soldering?
Yes. Jewellery assembly, model making, painting small parts, holding a phone board while a screen is lifted, and any job where a third and fourth point of contact helps. The arms are the tool, the context is yours.
Q: Does it come assembled?
The arms, base and magnifier arrive as a kit that threads together in a few minutes. No special tools are needed beyond what is in the box.
Customer Reviews
Payment and Security
您的支付信息已安全处理。我们不存储信用卡详细信息，也无法访问您的信用卡信息。